Find:

Location:

Ford Repair Questions

BRakes : 2000 Ford Explorer

Truck Model: 2000 Ford Explorer
Location: Fairfield, ME Submitted on November 25, 2012

Missy
Fairfield, ME

Replaced rotors, pads, and calibers. Bled system and have no brake pedal after starting vehicle.

Rate this Question:

Answers

  • Photo
    Eugene
    11 Franklin, MA
    (0) Rated this answer helpful
    Make sure you bleed with the pass rear then the  drivers rear then pass front then drivers front. Often you will have to do a few rounds to get all the air out. Sometimes if the brake pedal has gone to the floor the seals in the master can be damaged and the master will need to be replaced. 
    Posted on November 25, 2012
    Respond

    Need more advice? Ask our experts.

    Other Ford Related Repair Questions
    • Richard
      Hillsboro, OR
      Heater
      The colder it is outside the less heat I get from the heater at 30 degrees or colder very little heat.  Have changed the thermostat.
      1990 Ford F-150 | answers (1)
    • raul
      Othello, WA
      4/4
      My 4/4 is not getting power to selector checked fuses they are good 2008 ford f250 diesel heavy duty when I turn key on 4 X 4 light hi low comes on briefly need help turn switch nothing happens
      2008 Ford F-250 | answers (0)
    • Darin
      New Port Richey, FL
      1995 Ford F-150 | answers (2)
    • Kelly
      Salisbury, NC
      transmission swap
      I have an 85 Ford f-150.  It has an original AOD transmission. What other transmission can be substituted for that one.  Also the transmission is gone from the truck, how can I find out if it has a 10...
      1985 Ford F-150 | answers (1)
    • raul
      Othello, WA
      4 X 4 not working
      My 4th is not working In my diesel 6.4 truck checked fuses and relays I have no power to the 4 X 4 selector switch when I turn key on 4 X 4 indicators on dash light up briefly don't know what to check...
      2008 Ford F-250 | answers (0)
    • bill
      Terre Haute, IN
      engine change
      i got 2 rangers same year one is a 3.0 and the other is a 4.0 i blew up the 3.0 so can i take the 4.0 and put it in the place of the 3.0 will everything line up and bolt up
      2000 Ford Ranger | answers (1)
    • Junior
      Fort Wainwright, AK
      engine
      Vehicle is not running good.  I changed oil and did a drive test it was perfect.  A month ago I stop driving it because there was a weird sound coming from the engine that I have no clue what it is.  ...
      2007 Ford F-150 | answers (1)
    • Robert
      Santa Maria, CA
      Bad ignition switch symptoms
      Key was left on ran position, truck won't start, then it will start, rebooted computers, start won't start, hear clicking noise under desh is this a bad ignition switch????
      2000 Ford F-250 | answers (1)
    • tim
      San Diego, CA
      heat coming in cab while driving
       While driving heat is coming in the cab the engine is not heating up also thru the vents the air cont  just started been in storged for a while
      2003 Ford F-450/550 | answers (1)
    • Don
      Jones, MI
      no oil pressure
      Lost oil pressure replaced lower oil pump cranked and ran on either no oil pressure on gauge
      1995 Ford F-250 | answers (1)
    Shop Photo

    © 2014 MechanicAdvisor.com | Terms of Service | Privacy Policy

    We're working on making your car repair experience better.

    sign up to learn more about our groundbreaking new product

    Thank you, we will be in touch soon

    Your email will only be used to send information about our new project